Replacement Parts

Replacement Parts

Replacing The Baffles

Baffles get installed with the holes towards the rear of the stove. The 3 flanges of the baffles go on the back insulation, the side insulation and the channel running from back to front on the top of the stove. Stove. The screw applies pressure on the top plate to keep them in place.

To remove the old baffles, loosen the screw to create a space between the screw and the top plate. This will allow the plates to be pushed up, tilted and then dropped down. The new baffles can be placed as seen in the image above and the screws tightened to keep them and the insulation in place.

Replacement Parts

Replacing The Cub Fire Brick

Identification Of Pieces

LB = Left back (Side of stove)

LF = Left front (Side of stove)

RB = Right back (Side of stove)

RF = Right front (Side of stove)

BL = Back left (Back of stove)

BR = Back right (Back of stove)

Order Of Installation
  1. The Baffles are removed
  2. Old insulation is removed
  3. The sides get installed first
  4. The back gets installed second
  5. Baffles are installed to keep the new insulation in place

Things To Take Note Of

 LB and RB have bevels at the back to make way for the welds in the back of the stove

LF and RF have cut out to make way for the diffuser at the front of the stove below the window.

BL and BR have notches on the corner and the back to make way for the welds on the sides of the vertical channel and the weld at the bottom

Once installed, the baffles go in to secure everything in place. Baffles get installed with the holes towards the rear of the stove. The 3 flanges of the baffles go on the back insulation, the side insulation and the channel running from back to front on the top of the stove.

Replacement Parts

Replacing the Grizzly Fire Brick

Identification Of Pieces

LB = Left back (Side of stove)

LF = Left front (Side of stove)

RB = Right back (Side of stove)

RF = Right front (Side of stove)

BL = Back left (Back of stove)

BR = Back right (Back of stove)

B1 = Bottom (Bottom of stove)

B2 = Bottom (Bottom of stove)

Order Of Installation 

  1. The baffles are removed
  2. Old insulation is removed
  3. The sides get installed first
  4. The back gets installed second
  5. the bottom is installed third
  6. Baffles are installed to keep the new insulation in place
Things To Take Note Of

 

LB and RB have bevels at the back to make way for the welds in the back of the stove

LF and RF have cut out to make way for the diffuser at the front of the stove below the window.

BL and BR have notches on the corner and the back to make way for the welds on the sides of the vertical channel and the weld at the bottom

B1 and B2 have bevels at the bottom for the welds found at the bottom of the stove near the vertical channel at the back.

Once installed, the baffles go in to secure everything in place. Baffles get installed with the holes towards the rear of the stove. The 3 flanges of the baffles go on the back insulation, the side insulation and the channel running from back to front on the top of the stove.

Replacement Parts

Replacing The Glass

Start by removing the door from the stove and lay flat on a table. Then proceed to remove the four acorn nuts. Once the old glass is removed, place the new one in the same position as the original. Fix the cover plate in place by tightening the nuts. To ensure it is not too tight, loosen them by a quarter turn. And install the door back onto the stove.

We offer a warranty on the glass for the first 90 days of use.

ALL DAMAGE REQUIRES A PHOTO SENT TO CUBICMINIWOODSTOVES@GMAIL.COM.

CB-1299 Replacement Window Grizzly